Technical library for cars specialists
FR | ES | IT | NL | DE

Handbook Engine timing belt

1 pack, two pieces
a benefit from each, a place for each

From 1990 to 2009, all methods on 800 + pages !
33 makes, 580 models, 3600 versions
A4 Format (21 x 29,7 cm)

Handbook Engine timing belt
The book (A4) in the workshop
Removal/installation of the timing belt,
Setting, tension,
Tightening torque,
Tools required,
Drive belts path,
Numerous visuals: better user comfort is achieved through interwoving sequentially text and images.
The booklet (A5) at the desk, to feed the customer with solid data
Time scale
Replacement periodicity

Price net of tax:149.50 €
Ref:10MCDSEN

Enter your intra-community VAT number (start of this page)


Intra-community VAT number: OK
Publitest timing beltprint

accessibility

Time sched. belt + roller: 2.95

general instructions

Lift and block the vehicle.
Take note the radio-antitheft code.
Disconnect the battery.
Replace the drive belt.
Never turn the motor through the camshaft's pinion.
Unless specified otherwise, turn the motor in the normal rotation direction.
Apply all tightening torques.

demounting

Place the vehicle on a platform.
Remove :
  • The front/right wheel.
  • The guard casing of the engine.
  • The front/right wheel arch.
  • The cylinder head cover.
  • The ignition coils.
  • The drive belt.
  • The winding roller of the drive belt.
  • The pulley of the crankshaft.
  • The timing-gear covers.


demounting



caption

A2 pinion of the inlet camshaft.
A3 pinion of the exhaust camshaft.
B2 crankshaft pinion.
C2P waterpump pinion.
G2 guide roller.
G1 idler roller.
B1 crankshaft pulley.
O1 drive belt.
O5 balance shaft belt.
9 balanceshaft pinion.

removal of the belt of the balance shafts

Remove :
  • The sparks of the first cylinder.
Install :
  • A dial igauge T with an adapter in the central spark's well.

Install :
  • The tool to rotate the crankshaft pinion.
Turn :
  • Slowly the crankshaft B2 until the TDC on the n.1 cylinder.

Control :
  • The alignment of the markings A of the balance shaft.

Loosen :
  • The nut D of the idler roller G1b of the belt of the balance shaft.

Remove :
  • The belt O5 of the balance shafts.

Control :
  • That the crankshaft is definitely on the TDC of the n.1 cylinder.
Loosen :
  • The screw F holding the idler roller G1.
Slacken :
  • The timing belt O1.
Remove :
  • The timing belt O1.

Loosen :
  • The screws holding the intake camshaft pinion A2 while maintaining the pinion with the torque-blocking tool.
Remove :
  • The screw holding the exhaust camshaft pinion A3 while maintaining the pinion with the torque-blocking tool.

Remove :
  • The hats of the camshaft bearing.
Cylinder 3 exhaust side.
Cylinder 2 intake side.
Install :
  • The setting tool instead of the removed bearings.

Install :
  • The timing belt O1.
Stretch :
  • The belt to the maximum with the belttensioning tool.
Tighten :
  • The screw F holding the idler roller.
Tighten again :
  • The screws holding the exhaust and intake camshaft pinions with the torque-blocking tool.
Inlet :
Tightening torque 1,2 daN.m.
Exhaust :
Tightening torque 10 -> 12,4 daN.m.
Remove :
  • The setting tools.
Put back :
  • The hats of the camshaft bearing.
Tightening torque 1,3 -> 1,6 daN.m.
Turn :
  • The crankshaft two turns clockwise until the TDP at cylinder n.1.
Loosen :
  • The screw F holding the idler roller G1.
Align :
  • The mobile mark G of the idler roller with the aim-hole H of the cylinder block with the help of the tension tool E) (ref.1.822.149.00.
Tightening torque 2,1 -> 2,6 daN.m.



Remove :
  • The dial-gauge T.
Put back :
  • The plugs.

setting of the balance shafts belt

Control :
  • The alignment of the markings A of the balance shaft.
Put back :
  • Provisionally the lower cover of the timing belt.
  • Provisionally the crankshaft pulley B1.
Adjust :
  • The alignment of the markings B on the pulley and the cover C.
Remove :
  • The pulley of the crankshaft B1.
  • The lower timing cover.
Install :
  • The belt O5 of the balance shafts.
Make coincide :
  • The aim-hole J with the center of the rotation space I.


Tighten :
  • The nut D of the idler roller G1b of the belt of the balance shaft.

reassembly

Put back :
  • The remaining parts in reverse order of the removal.



© Publitest 2009
Copyright © Cyberdata - 4 rue Emile Pathé Bat2 78400 Chatou France - RCS Nanterre B 413 394 396 - Tous droits réservés Sitemap Twitter